Update of new Feature: Overclocking TVB:
OverClocking TVB is an extension of the TVB feature allowing you to customize frequencies according to temperature.
This, in my opinion, is a useful feature that milks the last bit you have got at light loads without requiring additional voltage. In a nutshell, it takes that 5~8C extra margin you’ve got, and converts it into additional frequency.
It is only supported on 10900K/non K variants atm, and maybe 10850K. IF unsupported, the information will display N/A
Everything TVB related is now grouped into the Thermal Velocity Boost menu:
At the top, it reads back the current configuration of the OCTVB.
For this to work properly, CStates must be enabled for proc to be active core aware! If you synch all cores, make sure you manually enable Cstates.
Active Cores refer to the row of settings applicable when that number of cores are active. Ratio Setting refers to the associated core ratio for that active core count. Temp A refers to Temperature A for that active core count above which the ratio would drop by it’s associated Ratio offset. This offset is the Negative Ratio Offset A pictured above. Temp B refers to Temperature B for that active core count above which the ratio would drop by a further 1x.
Let’s take a simple example below:
Right now Cpu runs at 50C and only core is currently active. Ratio is therefore 55x.
User does something, the active core gets hotter and becomes 72C, and still only 1 core active. Ratio now becomes 55-1=54x because 72c is > Temp A 68C and the negative offet is 1. If negative offset is 2 for eg, then it will become 55-2=53x.
And then, the user loads it further and now temperature is 82C. Ratio now is 55-1(from TempA) -1(from TempB) =53x because temp is > tempB of 78C and a further 1x is deducted. Temp B negative offset cannot be configured and is a fixed 1x.
Then the user does something different and now 3 cores are active. The applicable row becomes the third row in the picture above. CPU runs at 60C right now and so none of TempA/B has been exceeded, therefore ratio is the original 53x. then proc gets to 77C, TempA is breached, it’s associated offset is 3x so proc drops to 50X. Again it runs hotter still, gets to 87C. TempB is breached, proc drops a further 1x and ratio is now 49x. And the story continues…
Hopefully, this example is enough to explain.
The control is under Overclocking TVB, customize it using “Enabled”
When enabled, you get to customize the params for each row (each active core count) The Ratio, you configure it the main menu like you always do, whether you go with synch all cores (if you go with synch all cores pls manually enable cstates so that the proc can tell number of active cores) or by core usage it doesn’t affect this.
It can be very time consuming to customize it yourself, so we have made 2 predicted presets for you, the +1boost profile and +2boost profile
Just use it ON TOP of your current/maximized oc setting.
It will do an additional 1x/2x on top of your current setting and set auto-calculated temperature boundaries based on the associated frequency. This does not add voltage because it still uses the voltage before adding the boost and merely tries to scrap some performance from moments when there is thermal headroom.
So for example, I would load Ai optimized, then enable to +1boost. I find it stable, feel a bit adventurous, then I change it to +2boost and try.
Or my current OC is 54X @ 1.4v, I keep this and I just go into OCTVB to enable +1 boost. (if you go with synch all cores pls manually enable cstates so that the proc can tell number of active cores, or just use by core usage and set every core count to same value)
OverClocking TVB is an extension of the TVB feature allowing you to customize frequencies according to temperature.
This, in my opinion, is a useful feature that milks the last bit you have got at light loads without requiring additional voltage. In a nutshell, it takes that 5~8C extra margin you’ve got, and converts it into additional frequency.
It is only supported on 10900K/non K variants atm, and maybe 10850K. IF unsupported, the information will display N/A
Everything TVB related is now grouped into the Thermal Velocity Boost menu:
At the top, it reads back the current configuration of the OCTVB.
For this to work properly, CStates must be enabled for proc to be active core aware! If you synch all cores, make sure you manually enable Cstates.
Active Cores refer to the row of settings applicable when that number of cores are active. Ratio Setting refers to the associated core ratio for that active core count. Temp A refers to Temperature A for that active core count above which the ratio would drop by it’s associated Ratio offset. This offset is the Negative Ratio Offset A pictured above. Temp B refers to Temperature B for that active core count above which the ratio would drop by a further 1x.
Let’s take a simple example below:
Right now Cpu runs at 50C and only core is currently active. Ratio is therefore 55x.
User does something, the active core gets hotter and becomes 72C, and still only 1 core active. Ratio now becomes 55-1=54x because 72c is > Temp A 68C and the negative offet is 1. If negative offset is 2 for eg, then it will become 55-2=53x.
And then, the user loads it further and now temperature is 82C. Ratio now is 55-1(from TempA) -1(from TempB) =53x because temp is > tempB of 78C and a further 1x is deducted. Temp B negative offset cannot be configured and is a fixed 1x.
Then the user does something different and now 3 cores are active. The applicable row becomes the third row in the picture above. CPU runs at 60C right now and so none of TempA/B has been exceeded, therefore ratio is the original 53x. then proc gets to 77C, TempA is breached, it’s associated offset is 3x so proc drops to 50X. Again it runs hotter still, gets to 87C. TempB is breached, proc drops a further 1x and ratio is now 49x. And the story continues…
Hopefully, this example is enough to explain.
The control is under Overclocking TVB, customize it using “Enabled”
When enabled, you get to customize the params for each row (each active core count) The Ratio, you configure it the main menu like you always do, whether you go with synch all cores (if you go with synch all cores pls manually enable cstates so that the proc can tell number of active cores) or by core usage it doesn’t affect this.
It can be very time consuming to customize it yourself, so we have made 2 predicted presets for you, the +1boost profile and +2boost profile
Just use it ON TOP of your current/maximized oc setting.
It will do an additional 1x/2x on top of your current setting and set auto-calculated temperature boundaries based on the associated frequency. This does not add voltage because it still uses the voltage before adding the boost and merely tries to scrap some performance from moments when there is thermal headroom.
So for example, I would load Ai optimized, then enable to +1boost. I find it stable, feel a bit adventurous, then I change it to +2boost and try.
Or my current OC is 54X @ 1.4v, I keep this and I just go into OCTVB to enable +1 boost. (if you go with synch all cores pls manually enable cstates so that the proc can tell number of active cores, or just use by core usage and set every core count to same value)
