cancel
Showing results for 
Search instead for 
Did you mean: 

ROG MAXIMUS X HERO BIOS VER 1101 Feedback Thread

mr_allroy
Level 9
I just noticed this is on the ASUS US website. Has anyone tried it yet? I'm not feeling like being a guinea pig as "bios flashback" does not seem to work.

Anyways, let's keep this friendly and post our experiences with it.
281 Views
63 REPLIES 63

Carlyle2020 wrote:
hi bass junkie xl,

i can confirm higher loads using the same Bios config on both Versions:
i run:

asus x hero wifi

8700k lidded and a Noctua NH-D14 + NT-H1 paste

been using 5 ghz no avx offset

adaptive mode
totaly adaptive voltage - 1.305 v
offset - none ( default )
svid-best case cenario
svid - on
ia/dc load line - 0.001
load line cali= 4
on full load i get :

CPU core:1.312
CPU Vid:1.354 (With Bios ver. 1003 the power capped almost exactly at 1.300)


thats sounds pretty good but there is a issue

if i use 1.36v
adaptive
svid @ best case
svid on
ia/dc @ 0.001
load line 6

battlefield 1 vcore spikes up to 1.392 max chills around 1.372v for 70 % of the time and 1.36v about 20 % of the time .

if i droped my load line cali to level 5 i would drop down to 1.32 - 1.344v and i bet i would only get 1.36v 20 % of the time on load .

to counter that i would have to run 1.38v @ load line 5 sowhen under load i would get 1.36v under load but then my idol light loads would get 1.38 - 1.392

higher vcore @ light loads and perfect load volts @ high load or the other way around if i use level 6 .

i dont mind going up to 1.372 v when im stable @ 1.36v but i dont want more then 1.372v max
Rig # 1 - 14900K SP-115 | 87 MC @ 6.0 GHZ | 5.1 R | 4.5 E | DDR5 48GB @ 8,400 c36 | Strix RTX 4090 | XG27AQN 1440P 27" 360 Hz G-Sync ULMB 2

Rig # 2 - 13900KS-SP-120 | 80 MC @ 5.8 GHZ | 5.0 R | 4.5 E | DDR4 32GB @ 4,300 c15 | Strix RTX 3080 | Aoc 1080P 25" 240 Hz G-Sync

SMB_92
Level 9
If I go to 5ghz which I normally can at 1.29v, it will shoot over to 1.4v at LLC 4. Previously it would only shoot to 1.33,and rarely at that. So I took that profile away for 4.8ghz.

Pretty much same setup as Carlyle above except I'm under a Kraken X62 on the Apex board. I am seeing temps accompany the voltage spikes, at one stage I see 80c at 4.8ghz which is what I was maxing at 5ghz previously. Also now my 5ghz profile will occasionally show corrected whea errors in log, due to spectre patch and the now slight instability with all that volts.

Edit- okay just reverted to 1003 and the spikes are still present 😞

Praz
Level 13
Hello

Depending on the amount of tuning one wishes to do as well as IMC capability it is best to plan on memory speeds 2 to 3 bins lower than the max listed.

SMB_92
Level 9
My IMC is brilliant by the seems, I am able to run my Gskill 3200 C15 kit at just 1.05v on both IO and SA. Any bsod I had during testing was all vcore and settings around that.

Just noticed some odd behavior. I have heard of an issue with fans not ramping up, and I noticed mine were always quiet at load but temps weren't out of hand so I thought nothing of it.

Anyway, for fun I tried out the TPU setting and it went to 5ghz, 1.28v maxing 1.312. Thought that was cool but a bit low and sure enough it gave a vcore bsod (this one needs at least 1.29 I found). So I removed that and set my 4.8ghz profile. Now my fans ramp up properly, and the same settings from earlier is now maxing at 1.28v.

I am curious as to why that is. 5 reboots now and it hasn't changed.

SMB_92
Level 9
That's seems high for 5ghz? Or are you running more? I read that different CPUs have different VID behavior, that even with the settings / overrides on, if the processor is not happy with the volts at load it will shove more in regardless. Or perhaps at least try, I don't quite understand it fully cos I haven't experienced it with my 7700k or my 3960x. I always appreciated an little initial overshoot when I load comes on from idle volts (say from 0.7 to 1.28 the down to 1.25v in my case for my 4.8 profile), this seems to help preventing instability when a load comes on (something that I had to fine tune for on my 3960x)

SMB_92 wrote:
That's seems high for 5ghz? Or are you running more? I read that different CPUs have different VID behavior, that even with the settings / overrides on, if the processor is not happy with the volts at load it will shove more in regardless. Or perhaps at least try, I don't quite understand it fully cos I haven't experienced it with my 7700k or my 3960x. I always appreciated an little initial overshoot when I load comes on from idle volts (say from 0.7 to 1.28 the down to 1.25v in my case for my 4.8 profile), this seems to help preventing instability when a load comes on (something that I had to fine tune for on my 3960x)


i need 1.36v for 5.0 ghz no avx offset to be 24 hr stable in real bench , prime 95 , occt linpack .

1.36v on load that is .

i wouldnt say 1.36v is high for 5 ghz , alot of forums i read the average vcore i would say is 1.35v-1.4 v

i would say 1.4v for 5 ghz is high .

i dont mind a little over shoot but 1.36v adaptive no offset i get spikes to 1.392 v on havey load .

if i use a load line cali less then 6 i volt drop below my set 1.36.

i notice the cpu and svid give the cpu 0.016v incriments under load so if i use a -0.016 offset with 1.36v total adaptive mode then it gets better but then i drop down to 1.344 v and then get 1.36v 40 % of the time under load and only spikes to 1.372v witch isnt bad . but im worried that when it drops down to 1.344v when light loads it might give me a whea error eventualy none yet though .

ill try load line level 5 but im going to have to use a higher vcore like 1.38v so when under load i get 1.35v - 1.38v
Rig # 1 - 14900K SP-115 | 87 MC @ 6.0 GHZ | 5.1 R | 4.5 E | DDR5 48GB @ 8,400 c36 | Strix RTX 4090 | XG27AQN 1440P 27" 360 Hz G-Sync ULMB 2

Rig # 2 - 13900KS-SP-120 | 80 MC @ 5.8 GHZ | 5.0 R | 4.5 E | DDR4 32GB @ 4,300 c15 | Strix RTX 3080 | Aoc 1080P 25" 240 Hz G-Sync

will_s
Level 7
it improved myboot times for when the Rog startup screen appears.........had to disable CPU fan as it wouldnt boot ( not sure what my 115i pro is plugged into )

edit: post still twice as long as new Asrock K6 with 8600K ( just oc it to 5000 with 1.3 volts not that I had any real clue on what I was doing)
will

SMB_92
Level 9
Oh so your running with no AVX offset, I think mine was requiring about the same in that Occt test for AVX but too hot so I bring offset to 2 for 5ghz to keep the 1.292v happy. Otherwise whea.

Always seems like 1.4v is the ceiling for health, was so with 3960x not sure for other between then and 7700k/8700k.

Regarding boot time mine seems to spend a bit of time at Post the same way my Rive did, seems to come on and then flash for a sec then show rog screen again for a few secs, then boot time to Windows logo is almost instant. I guess rog boards really go hard with the Post/training?

cold boot test with

-fast boot enabled in bios
-csm disabled
-intel 600p m.2 ssd
- 2 hdds
-ram xmp @ 3000 mhz @ manual 4000 mhz cl 18
-ram tweak mode 1
-ram trainning on ( default )
-mch full check auto ( on )

power bottom pressed to the windows desk top sound is 28 seconds ( windows 8.1 x 64 )

-mch full check off
-ram training off

25 seconds .
Rig # 1 - 14900K SP-115 | 87 MC @ 6.0 GHZ | 5.1 R | 4.5 E | DDR5 48GB @ 8,400 c36 | Strix RTX 4090 | XG27AQN 1440P 27" 360 Hz G-Sync ULMB 2

Rig # 2 - 13900KS-SP-120 | 80 MC @ 5.8 GHZ | 5.0 R | 4.5 E | DDR4 32GB @ 4,300 c15 | Strix RTX 3080 | Aoc 1080P 25" 240 Hz G-Sync

bass junkie xl wrote:
cold boot test with

-fast boot enabled in bios
-csm disabled
-intel 600p m.2 ssd
- 2 hdds
-ram xmp @ 3000 mhz @ manual 4000 mhz cl 18
-ram tweak mode 1
-ram trainning on ( default )
-mch full check auto ( on )

power bottom pressed to the windows desk top sound is 28 seconds ( windows 8.1 x 64 )

-mch full check off
-ram training off

25 seconds .


not good , my Asrock does it in half the time

The Hero does it in about 20 seconds ( up to Win10 logon screen )

But new BIOS is quicker but not by much
will