cancel
Showing results for 
Search instead for 
Did you mean: 

[GL702VM & similar] Solution to Performance issues / Overheating / Throttling / Whine

onjax
Level 9
Hi guys, I bought GL702VM and was upset with its ability to handle games and high load. I had immediate temperature jump to over 85 jump and throttling / frame drops in games. So I decided to understand how to improve things, even though, I already lost my warranty due to my experiments, but at least I can answer for everyone, that:
- the main problem of this notebook is inefficient, insufficient cooling system with too thin fans, too small heatsinks, vent holes in a wrong places (aside, not above the fans).

To prove this, I first changed the thermal interface to liquid metal. That doesn't solve the issue. This proves, the thermal contact is ok, but heat dissipation is bad. Second, I ran stress tests with back cover removed - helped a lot, about 15-20 degrees off. The proves that air intake is wrong in this system.

I also removed an antidust tape with holes covering all the intake holes. That helped by around 5 degrees and also brought down air noise.

Then I came to idea of downvolting CPU and GPU, thanks to devs of ThrottleStop and MSI Afterburner, we can do this with relative ease.

The result: Fan noise reduced by half. Temp drop is huge. More speed due to ability of CPU/GPU to properly boost to max speed.

For your information - CPU is responsible for about 30% of heat, GPU - for 70%. So best idea is to undervolt the GPU, but for best results go for both.

THE GUIDE - CPU
Variant A - Install Intel Xtreme Tuning Utility

  • Go to Advanced Tuning tab and Change Dynamic CPU Voltage Offset to negative value (move slider to the left). -100mV is a good starting point. Leave Mode to Adaptive.
  • Apply changes.

My CPU holds -150mV well.

Variant B - Install Throttle Stop 8.3 or above

  • On main window click FIVR button
  • Under CPU Core Voltage move Offset Voltage slider to the left. -100mV is a good starting point. The lower value the less heat.
  • Click Apply. On the same window you can save settings to make them apply every time you start the app.


THE GUIDE - GPU

  • Download and Install MSI Afterburner 4.3 or above
  • In settings turn on Unlock voltage control and Unlock voltage monitoring
  • Close MSI Afterburner
  • Download my Voltage Profile for GTX 1060
  • Extract profile to some folder and then copy file to "C:\Program Files (x86)\MSI Afterburner\Profiles". Click continue as Administrator when Windows asks permission to write.
  • Run MSI Afterburner, click on profile 1 (out of 5). Then press Ctrl+F. (1 - least heat, but may be unstable for some... 2, bit more voltage etc till 5.)
  • You will see my Voltage Curve (screenshot). What you'll see that it's flat until 1050mv. that means. 1050 will never be used, so will never be used any voltage except 831mV @ 1860 MHz and below.
  • Click apply to test this curve
  • If this curve is not stable for you - edit it to your taste: Click on 831mV dot and move it lower, so that lower freq will be used for that voltage, and for 1860 freq next available voltage will be used. Etc. Work with leftmost voltage dots to make everything stable.


This curve drops heat of GPU by at least 30%, which is huge.

THE GUIDE - COIL WHINE
Workaround described here: https://support.microsoft.com/en-us/kb/975530

Perform only these steps as Administrator:
1. At a command prompt, run the following command:
reg add HKLM\System\CurrentControlSet\Control\Processor /v Capabilities /t REG_DWORD /d 0x0007e066
2. Restart the computer.
3. Run ThrottleStop v8.3 or above and uncheck C1E. Click save.

In theory, it will make CPU a bit hotter while system is idle, because it disables some advanced C-states, but i didn't notice that in monitoring app.
That solved like 99.9% of the noise, and in addition, disabling C1E in ThrottleStop solved noise issue completely.
911,063 Views
1,122 REPLIES 1,122

87262
Do you know the name of this tape?

Also is it safe to add this on ports

Jam31337
Level 7
Hi, please share RTX 2070 mobile Afterburner profiles if you have them.
Also, did anyone repaste the Asus ROG STRIX G15 G512WL? I would appreciate information on this and pictures would be great!
I've used MSI afterburner and set my core clock -500 Mhz (minus five hundred) and there is no change in temps at all, maybe 2-3 degrees which doesn't make any sense. I've disabled CPU boost so on 100% CPU load my laptop is locked to stock 2.3Ghz and is still rocking low 80 celsius. Any suggestions?
I'm planning to get thermal grizzly conductonaut and repaste the CPU+GPU bcz I can't believe Asus did add liquid metal as a thermal interface to my laptop which is using a 10875H + RTX 2070 which are both super hot on the same heatsink.

Repasting is a good solution