...

[MoKiChU]

...

[Kazuma88]

Mappi75 wrote:
Wondering - for me 1302 (Hero) works much better than 1105 - first time that 32 DDR4-4000 CL17-17-37-2N will run at full speed & lower voltages stable.

I do not know what to say. I've always done the usual procedure: Clear CMOS, BIOS update. Restart on Windows and shutdown. Again Clear CMOS and "restore" by hand the old settings: such as the frequency of the ram memory, the CPU voltage, etc .... Maybe there is something enabled or disabled by default that I haven't seen? :confused:

Two new things I noticed are within the BOOT entry that refer to RECOVERY.

[1mluer]

1302 on my XI Apex is having issues with CPU throtteling. I turned on performance settings in windows and turn off speed step in bios as well as C states. it still throttles back and knocks almost a 1000 off my cinebench r15 scores. They went from 2300 to 1490

Anyone having issues with Throttling too ?

[1mluer]

1mluer wrote:
1302 on my XI Apex is having issues with CPU throtteling. I turned on performance settings in windows and turn off speed step in bios as well as C states. it still throttles back and knocks almost a 1000 off my cinebench r15 scores. They went from 2300 to 1490

Anyone having issues with Throttling too ?

Ok fixed it. I had to turn off all software control limits just under the XMP profile. 🙂

All good back to 2300 again 🙂


Now if I can just get the lighting service to run on cold bootup without having to be restarted and periodically crashing my game and itself, I would be perfectly golden. with AURA it's asking a lot over the last 10 months this issue has been around.

[Carlyle2020]

My 8086 runs fine. With and without power saving settings.
... Isn't the "turbo" function diretcly below the speed step setting? *wink, wink*

Regards
Carlyle

[D_9]

Good day to all!
Is it possible to adjust the minimum speed on the connector W_PUMP from 30% of the speed, and not as it is now from 60%?

[M2k1980]

im getting these high voltages on cpu system agent since i got my board with v0805, and my ram is only working fine with 1.37v or games exit without any messages

[cniedzi]

M2k1980 wrote:
im getting these high voltages on cpu system agent since i got my board with v0805, and my ram is only working fine with 1.37v or games exit without any messages

Did you try to manually set these voltages?

[M2k1980]

yes ofc i did, i set to 1.10 and 1.15 and its working fine

[MoKiChU]

...

[MrAgapiGC]

MoKiChU wrote:
Hi everyone,

New BIOS 1302 [20/09/2019] for ROG Maximus XI Code/Extreme/Formula has just been released :

ROG MAXIMUS XI CODE : https://dlcdnets.asus.com/pub/ASUS/mb/LGA1151/ROG_MAXIMUS_XI_CODE/ROG-MAXIMUS-XI-CODE-ASUS-1302.zip

ROG MAXIMUS XI EXTREME : https://dlcdnets.asus.com/pub/ASUS/mb/LGA1151/ROG_MAXIMUS_XI_EXTREME/ROG-MAXIMUS-XI-EXTREME-ASUS-130...

ROG MAXIMUS XI FORMULA : https://dlcdnets.asus.com/pub/ASUS/mb/LGA1151/ROG_MAXIMUS_XI_FORMULA/ROG-MAXIMUS-XI-FORMULA-ASUS-130...

Thread updated.

Good news. I will wait on the OEM page gets updated so i can check it out. thanks in advance