07-22-2020 12:59 PM
07-23-2020 10:00 AM
07-23-2020 11:41 AM
Silent Scone@ASUS wrote:
1) VCCIO and VCCSA are signal rails, which means too much voltage can be just as detrimental as too little. You will need to find a value that works well for your CPU sample and memory kit.
2) This shouldn't be necessary if the desired XMP profile voltage is input. However, depending on the amount of guard band put in place by the memory vendor, it may be beneficial to try adding voltage (10-30mv).
3) Those readings are normal as the voltage is tapped off the power plane, so will not always be matched to what is being fed at the DIMM.
4) Each individual CPU is different, as a rule of thumb these values should be within 100mv of one another. VCCSA has the larger impact on stability with memory overclocking.
5) Depending on the course of the instability, you may require more vcore to accommodate for the increased memory frequency due to the increase in I/O.
07-24-2020 05:41 AM
Thank you very much for your answers!
Can you please elaborate more a lit bit about this " Those readings are normal as the voltage is tapped off the power plane, so will not always be matched to what is being fed at the DIMM." So if i set 1.35V in bios and bios shows me only 1.3250, should i increase voltage till i see that the actual reading is 1.350v in bios? So with VCCSA and VCCIO, i set them the same voltage, but actual reading a very different for them. So should i try to keep them equal in what i set in bios or should i try to keep them equal in actual readings?
08-06-2020 06:31 AM
08-06-2020 11:03 PM
08-14-2020 06:25 AM
Silent Scone@ASUS wrote:
If using Adaptive Vcore, it's common that more voltage is needed over a fixed/manual voltage due to the change in load transitioning. It is also preferable to increase Vcore if experiencing instability than increasing LLC.
Also, be aware that it is not possible to set a lower Aditional Turbo Voltage than the stock VID for a given ratio.
08-14-2020 03:40 PM
08-16-2020 10:55 PM
Can anyone here help with my situation?.. I've no luck trying to find a post about the (ROG Strix Z490-G)
I've had nothing but issues from the start with this board and manage to make it work after hours upon hours for 2 days!...
Now here's my situation : For some odd reason DIMM Slot 1 is not allowing me to run the PC, I get that Yellow indicator on the board "Memory Issue" at first I thought it was the memory stick gone bad, but this only happens when I set it on (Slot 1) ??.. I have switched the memories around and its the same problem? - I'm not even running XMP.
- I run 1 Stick on Slot 2 no problem.
- I run 2 Sticks on Slot 2,4 no problem.
- I run 3 Sticks on Slot 2,3 and 4 no problem.
- Slot 1 is giving me problems...
I cant even update to the latest LAN Driver v.188.8.131.52. and I went through the ridiculous steps:
ntel(R) Gigabit Ethernet Driver V184.108.40.206 for Windows 10 64-bit.
Before installing Intel I225-V driver v.220.127.116.11, please ensure that Intel I225-V firmware should be updated to v.1.45 via firmware update tool. After finishing necessary firmware update, please shut down and unplug the power cord then reboot the system normally. For more information, please refer to the firmware update guide.
I cant even update to the latest BIOS v0607 I went through the again the ridiculous steps:
ROG STRIX Z490-G GAMING BIOS 0607
"1.Improve system performance and stability 2.Improve compatibility with the Intel H10 Optane Module 3.Enhance AI Cooling mechanism
Before running the USB BIOS Flashback tool, please rename the BIOS file (SZ490G.CAP) using BIOSRenamer."
When I look into the file and use open the "BIOSRenamer" I see the same (SZ490G.CAP) already there, so I copy the CAP file into the root (USB FAT32) go into BIOS - Tool - "EZ Flash 3" I get a message saying SZ490G.CAP it's the wrong file?????...Something like that and I then go the old way at the back of the Board hit the Flash Button hold it for 3 seconds and nothing happens??... No LED indicator, because it's not doing anything...
Asus have the worst customer service or tech support from my personal experience, especially now with this COVID-19 that's like extreme! - That's why I'm here on the forum.
10-04-2020 05:59 AM