OverClocking 4770K ?

[LiveOrDie]

What voltages and temps should i be looking at i read a few guides and watch a few video but they dont really tell you whats safe in the means of running it 24/7?

[HiVizMan]

Temps are the only thing I can give you a number too.

Between 10 and 15'C higher than your ambient for idle and below 85'C for under load.

Voltage is about your CPU and the temps that it causes when applied. But you would want to stay below 1.4 for 24/7 use in my view.

[LiveOrDie]

For some reasons my temps have lowered this is at 4.6Ghz 1.25Volts but when i run LinX my temp go though the roof and i have to stop the test.

---------------------------
--- Testing Processor 1 ---
---------------------------


--- IPDT64 - rev 1.29.0.0.MP ---


--- Start Time: 10/27/2013 21:56:45---


--- Skipping Config ---


--- Reading CPU Manufacturer ---

Expected --> GenuineIntel
Detected --> GenuineIntel
Found --- Genuine Intel Processor ---

--- Temperature Test ---

Temperature Test Passed!!!


Temperature = 47 degrees C below maximum.


--- Reading Brand String ---

Detected Brand String:
Intel Core i7-4770K 3.50GHz

Brand String Test Passed!!!


--- Reading CPU Frequency ---

Expected CPU Frequency is --> 3.50


Detected CPU Frequency is --> 3.50009

CPU Frequency Test Passed!!!


--- FSB NOT Supported on this Processor ---


--- Running Base Clock test ---


Detected Base Clock --> 100
Base Clock test Pass ---
..QPI rate Test not supported..
..Skipping QPI rate Test..

Skipping QPI rate Test


--- Running Floating Point test ---


Million Floating Points per Second, MFLOPS --> 561.6
Floating Point Test Pass ---

--- Running Prime Number Generation Test ---


Operation Per Second--> 4.65205e+006
Prime Number Generation Test Pass ---

--- Reading Cache Size ---

- Detected L1 Data Cache Size --> 4 x 32
- Detected L1 Inst Cache Size --> 4 x 32

- Detected L2 Cache Size --> 1024
- Detected L3 Cache Size --> 8192


Cache Size Test Passed!!!


--- Determining MMX - SSE capabilities ---


--- CPU FEATURES DETECTION FOR ---
--- MMX SSE ---
MMX - MMX Supported --> Yes
SSE - SSE Supported --> Yes
SSE2 - SSE2 Supported --> Yes
SSE3 - SSE3 Supported --> Yes
SSSE3 - SSSE3 Supported --> Yes
SSE4.1 - SSE4.1 Supported --> Yes
SSE4.2 - SSE4.2 Supported --> Yes
--- MMX SSE - capabilities check complete ---

MMX Test Result --- PASS
SSE Test Result --- PASS
SSE2 Test Result --- PASS
SSE3 Test Result --- PASS
SSSE3 Test Result --- PASS
SSE4.1 Test Result --- PASS
SSE4.2 Test Result --- PASS
MMX SSE Testing Passed !!

--- Determining AVX AES PCLMULQDQ capabilities ---


--- CPU FEATURES DETECTION FOR ---
--- AVX/AES/PCLMULQDQ ---
AVX - Advanced Vector Extensions Supported --> Yes
AVX OS Support - AVX Operating System Supported --> Yes
AES - Advanced Encryption Standard Supported --> Yes
PCLMULQDQ - Polys Carry-Less Multiply Supported --> Yes
--- AVX AES PCLMULQDQ capabilities check complete ---

AVX Compare Test Result --- PASS
AES Test Result --- PASS
PCLMULQDQ Test Result --- PASS
AVX AES PCLMULQDQ Testing Passed !!

--- Reading Memory Size ---


Detected Memory Size is --> 16.00GB


--- Integrated Memory Controller Stress Test ---


--- Integrated Memory Controller Stress Test Pass!!! ---


Integrated Memory Controller Test Pass!!!


--- Platform Controller Hub Test Disabled ---


..
..Query 2..
..
--- Querying for Intel(R) Integrated Graphics Device (IGD) ---
..Did not detect Intel(R) Integrated Graphics Device (IGD).
..This could be that the test platform is using a discrete graphics card.
..To test IGD, verify that there is an onboard video connector,
..shutdown the test platform, remove the graphics card, and
..move video cable from graphics card to onboard video connector
..Skipping Intel(R) Integrated Graphics Device Presence Test..
..

--- CPU Load ---


--- Load Level = 8


CPU Load Passed!!!


--- Temperature Test ---

Temperature Test Passed!!!


Temperature = 46 degrees C below maximum.


--- Test End Time: 10/27/2013 22:00:44---

[LiveOrDie]

Seems like 4.4Ghz on a H100i for my chip is max 1.18v

[HiVizMan]

If your temps go through the roof at 1.26 then I would suggest there is a problem with the mount or the cooler.

[LiveOrDie]

That doing a stress test on 1.26 temps go over 90c .

[HiVizMan]

Still seems very high to me. I did not see beyond 80 with 1.26 and the H100.

Could someone else comment what their temps were like with the H100i please.

[LiveOrDie]

I would like to know to but even when watching the newegg asus OC video for the top notch water loop they where running he said it could only do 1.3v on a stress test, Im running MX5 i only applied it to the CPU no the water block as well do you think it mite be to thin?

[HiVizMan]

If anything it would be to thick.

You only want sufficient TM to fill in the microscopic spaces. I use less than a rice grain amount for all my mounts.

[LiveOrDie]

I used about two rice grains but i applied it to the whole CPU using a scraper so probably lost a bit spreading it out.