cancel
Showing results for 
Search instead for 
Did you mean: 

TUF Z790 GAMING PLUS WIFI D4 not posting

Ntinsky
Level 9

My one week old motherboard suddenly started flashing the onboard RGB lights every time i try to power on the computer. I have everything disconnected from the board except the CPU and 2 DIMMS.

All started yesterday as i was daisy chain connecting some of the fans that my new case came with. I am using a MEshify 2 RGB.

At first the RGB switch didnt want to work well with the fans, so i connected them on the onboard RGB header.

It was then when the motherboard stopped working.

None of the QLED indicators is on, just the RGB blink. I ve send my PSU (Corsair RM850X) for a check and service claimed that it works without any issues.

Here is a video of the symptom
https://www.youtube.com/shorts/pLjk45pBao4


Any ideas?




226 Views
1 ACCEPTED SOLUTION

Accepted Solutions

Ntinsky
Level 9

So after a painful "take everything out and start over" session, i managed to have all systems up and running. I am not sure what the root cause was but after carefully connecting one component at a time, booting to post,power off, connect next component,repeat the issue has been resolved.

View solution in original post

5 REPLIES 5

JohnAb
Level 17

If you're saying that you connected the fans to the RGB header, I think that's your problem. Does the motherboard stop flashing if you disconnect the fans and RGB connectors? I suspect that too much current is being drawn and the flashing indicates an overload.  

Z690 Hero, 12900K, BIOS 4001, MEI 2433.6.3.0, ME Firmware 16.1.32.2473, 7000X Case, RM1000x PSU, ASUS TUF OC 3090TI, 2 x 16GB Corsair RAM @ 5200MHz, Windows 11 Pro 23H2, Corsair H150i Elite AIO, 4x Corsair RGB fans, 3x M.2 NVME drives, 2x SATA SSDs, 2x SATA HDs.

JohnAb
Level 17

I might have misread your post. If already disconnected and it still flashes, then probably not a good sign. If it was an overload, then it could be damaged. 

Z690 Hero, 12900K, BIOS 4001, MEI 2433.6.3.0, ME Firmware 16.1.32.2473, 7000X Case, RM1000x PSU, ASUS TUF OC 3090TI, 2 x 16GB Corsair RAM @ 5200MHz, Windows 11 Pro 23H2, Corsair H150i Elite AIO, 4x Corsair RGB fans, 3x M.2 NVME drives, 2x SATA SSDs, 2x SATA HDs.

No worries. The case has an independent  controller besides the one on the motherboard. I have tried both options separately but the result remains the same. All the above with only cpu and dimm on different slots to test for errors. QLED remains clean.

 

What i haven't tried is take everything out of the case and start connecting piece by piece after testing for post signal. I will try that tomorrow and come back with some feedback. For the moment i am too tired to think of any other cause

OK, sounds like a plan, good luck

Z690 Hero, 12900K, BIOS 4001, MEI 2433.6.3.0, ME Firmware 16.1.32.2473, 7000X Case, RM1000x PSU, ASUS TUF OC 3090TI, 2 x 16GB Corsair RAM @ 5200MHz, Windows 11 Pro 23H2, Corsair H150i Elite AIO, 4x Corsair RGB fans, 3x M.2 NVME drives, 2x SATA SSDs, 2x SATA HDs.

Ntinsky
Level 9

So after a painful "take everything out and start over" session, i managed to have all systems up and running. I am not sure what the root cause was but after carefully connecting one component at a time, booting to post,power off, connect next component,repeat the issue has been resolved.