Hey I just got a pcie 5.0 2tb aorus 10000 m.2. It was working fine at pcie 5.0, I cloned my C drive onto it and now it won't run at 5.0 it keeps reverting to 4.0. I switched the m2_1 setting to pcie 5.0 to no avail. Anyone having any problems with these new drives?
Alrighty so a little update. So after reinstalling drivers, reflashing bios, I reinstalled windows, the drive is still stuck at 4.0. I have no idea what happened to the drive or god forbid, if there is somthing wrong with the Pcie 5.0 lanes on the M2_1 slot. I am convinced the drive is borked and am going to exchange it at microcenter tomorrow. Asus really couldn't figure out what was wrong but, this is the last thing I can try to get it back to Pcie 5.0
Thanks for all your help guys. I can tell you that I have finally resolved what happened.
I reinstalled the NVME drivers, I reinstalled windows 11, I re-flashed the BIOS and enabled GEN 5 settings on my motherboard. I removed all SATA drives and still no luck. I then went and purchased a replacement for the drive that was not functioning and all I did was remove the previous drive and install the new drive. These are identical drives the only difference is that one was cloned with Acronis and one came from microcenter. After installing the new drive, lo and behold, the drive is transferring at the correct PCIE 5.0 speed and I have had no issues. Some how, some way, the Acronis disk cloning borked the drive into convincing itself that it was another Samsung 980 pro PCIE 4.0 instead of the Aorus 10000 PCIE 5.0 drive. I can't understand how cloning the drive could wipe out the PCIE 5.0 capability and keep it stuck at 4.0. SO..... anyone attempting to clone with Acronis beware the cloning process if going from pcie 4.0 to 5.0 it is def treacherous. I spend a week pulling my PC apart to fix this disaster.
Huh, that's a blast from the past, that I didn't think would be likely for NVMe drives. About 25 years ago, I encountered the same thing cloning a Unix OS between 2 Seagate SCSI 2GB drives using the equivalent of "dd if=/dev/sda of=/dev/sdb", and managed to change the reported model number of the target drive. Fortunately both drives were exactly the same spec and geometry in that case, just two different model numbers. Some part of the drive's internal configuration was read-write and included within the normal addressable blocks of the device. I never did dig fully into it, and the new drive with a bit of an identity crisis worked just fine, so I just switched to cloning at filesystem level instead for future cases.
What I find most surprising here is that the problem occurred with an official cloning tool, rather than some low level manipulation of devices.
I've seen strange issues when cloning, in that Windows can get confused if the old drive is still present - it thinks it can see the same drive twice and then one won't initialise. That's understandable I suppose, as it would be cloning the drive identifier information in Windows too. But who knows, maybe it was the cloning that did the damage. A complete mystery to me lol. Mind you, there is rather a lot that I don't understand to be honest 🙂 and as I get older, that probably won't improve.
Last time I tried to clone I used Clonezilla and couldn't get it to work properly. It seemed to have worked, but wouldn't boot from the drive. I tried to fix that, but gave up. I used to use it for regularly for OS backups and it was very good generally. Then I tried Macrium Reflect and that worked like a dream. It's free and still my preferred software for such tasks, just in case anybody wants to try it.
Z690 Hero, BIOS 2703, MEI 23184.108.40.206, ME Firmware 220.127.116.114, 7000X Case, RM1000x PSU, i9 12900K, ASUS TUF OC 3090TI, 2 x 16GB Corsair RAM @ 5200MHz, Windows 11 Pro 22H2, Corsair H150i Elite AIO, 4x Corsair RGB fans, 3x M.2 NVME drives, 2x SATA SSDs, 2x SATA HDs.