©ASUSTEK COMPUTER INC. ALL RIGHTS RESERVED.

Shamino · ‎05-21-2020

Shamino · ‎05-30-2020

MacClipper wrote:
Using a plain Dell USB keyboard attached via the Aten CS1784A kvm. Keyboard setup works well with all other Asus mobos used so far.

On the Z490 Hero WiFi model, still getting occasional "keyboard not found" USB errors in BIOS only with all the BIOS versions tried - 0222/0503/0509/0606. 100% successful workaround is to unplug and replug into the other USB2 port when that happens, minor issue but annoying nonetheless when changeing BIOS options.

CSM option is already enabled. Any suggestions?

just observe if its after entering of os by doing this:
from a clean G3->S5, ie from AC no power to AC power, boot and enter bios but not os, and keep rebooting without entering the os but just the bios and see if not found issue still there.
if it only exhibits this issue after the os then prolly check drivers.
ive seen similar on other platforms occassionally from certain oses, think related to usb drivers in the os.

Huypho · ‎05-30-2020

Thank you so much, I was having a really annoying issue with my z490-E where anytime I completely shut my system off and reboot, my computer wouldn’t recognize my m.2 drive and the only way to fix it is to reseat it. Updating to 0606 fixed the issue!

Zhiyuan_Lin · ‎06-02-2020

Can you provide changelogs?

Kilner · ‎06-04-2020

0607 now avalible for apex on the website ive been havng massive issues with avx currently as soon as enable it with all set voltages still crash yet its stable avx none avx wth teh same voltage dont make sense

benkey71 · ‎06-04-2020

They have put up the 0607 full release to replace the 0607 beta

I have updated from 0607 beta to 0607 full and my system feels more stable.
I'm on MAXIMUS XII EXTREME upgraded from my MAXIMUS X CODE to try the new
Intel chips and all good so far , runs a bit warmer but figured that.

Falkentyne · ‎06-04-2020

benkey71 wrote:
They have put up the 0607 full release to replace the 0607 beta

I have updated from 0607 beta to 0607 full and my system feels more stable.
I'm on MAXIMUS XII EXTREME upgraded from my MAXIMUS X CODE to try the new
Intel chips and all good so far , runs a bit warmer but figured that.

In what way did your system "feel" more stable? Usually, it is or it isn't 🙂
Feel is very subjective. What exactly changed for you, in what way, and what were you having issues with before?
Any specifics? I would guess that 0606 to 0607 should be a minor update with a few fixes, not a major code branch change.

Kilner · ‎06-05-2020

from my testing 0607 not limits io and sa voltage at 1.05 no matter what you set yet the older bios would drive these past 1.6v auto also somthing changd with vcore vault on 0607 im thinking of going back to 0607 as i can set vcore at 1.47 bios yet in windows shows 1.44 cpuz and my multimeter shows 1.48

0606 shows same vcore in bios as cpuz an multimeter was 0.03v higher

this issue now is the volts are a ta lower on the vcore so you have to bump it up another +5 in the bios for stability and when pushing hard that +5 makes you tip over the edge on heat

im havng an ssue with the rng ratio and my ram if i let ram default an just oc i can have high ring ratio no errors but as soon as i oc my ram i start gettng ring error (cache)

not sure what is going on also my vdroop is really bad on level 5 if im set at 1.47 i drop to 1.325 on load

lvl 8 holds vcore perfect and shows stabale voltage on the multimeter but im not sure if its spiking high due to all th miss information around llc 😞

Falkentyne · ‎06-05-2020

Kilner wrote:
from my testing 0607 not limits io and sa voltage at 1.05 no matter what you set yet the older bios would drive these past 1.6v auto also somthing changd with vcore vault on 0607 im thinking of going back to 0607 as i can set vcore at 1.47 bios yet in windows shows 1.44 cpuz and my multimeter shows 1.48

0606 shows same vcore in bios as cpuz an multimeter was 0.03v higher

this issue now is the volts are a ta lower on the vcore so you have to bump it up another +5 in the bios for stability and when pushing hard that +5 makes you tip over the edge on heat

im havng an ssue with the rng ratio and my ram if i let ram default an just oc i can have high ring ratio no errors but as soon as i oc my ram i start gettng ring error (cache)

not sure what is going on also my vdroop is really bad on level 5 if im set at 1.47 i drop to 1.325 on load

lvl 8 holds vcore perfect and shows stabale voltage on the multimeter but im not sure if its spiking high due to all th miss information around llc 😞

Are you using translation software to write this post? Because some things you wrote I don't understand, or they don't make sense. "Vault"? What does "vault" mean?

"going back to 0607" <--what? Did you mean "going back to 0606"? Please check your posts for accuracy. This stuff is confusing to read.

Also the very first sentence you wrote makes no sense either. "0607 not limits io/sa to 1.05v, yet the older bios sets this at 1.6v?" What do you mean "Not limits"? Sounds like you're saying the same exact thing. Maybe you meant "0607 limits IO/SA to 1.05v on auto, but 0606 sets it as high as 1.6v, if set on auto?"

Also, Level 5 LLC: 1.47v Bios-->1.325v load--this is proper behavior. Seen this on all bioses.

Bios: 606 shows same vcore in BIOS as CPU-Z? This should not happen, unless you are using LLC8. CPU-Z Vcore should always be lower than bios vcore, even on LLC7 it may be about 11-12mv lower (example: 1.470v-->1.459v).

And you should never use LLC8. LLC8 only for testing, and only at 1.25v or lower Bios set voltage.

"0606 shows same vcore in bios as cpuz an multimeter was 0.03v higher " <--what LLC?? Again, same vcore in BIOS and windows idle CPU-Z should never happen, except at LLC8.

Overclocking RAM stresses the IMC. Higher ring ratio when overclocking RAM will require more CPU Vcore, or higher VCCIO/VCCSA. Maybe both. This is normal behavior. Higher ring ratio will give more memory bandwidth (read, write, copy, maybe latency too). It is all related.

orcinus · ‎06-09-2020

All out of sudden, for no aparent reason, this morning the system woke up terribly slow. POST was terrible, Windows crashed to BSOD mid idle and BIOS is incredibly sluggish. CMOS reset did not help. There was no overclock. UEFI v is 0607,...

tomjaffery · ‎06-17-2020

Hp printer connect wifi becomes a straight forward task with hp software tools. Hp offers you the innovative quality of printers due to the task of hp wireless printer setup hassle-free. Maybe, your operating system not up to date or facing some network issues that become the task of hp printer setup wifi full of technical Hassles. Hp Printer Connect provides you some simple steps to help print wifi direct quickly.

You are going to unbox your hp printer first time. You got an instruction manual or hp printer driver CD. In case, your hp printer driver CD lost, or maybe it’s not working with your CD ROM. As a result, you can set up your printer without CD wireless with your network. First of all, keep the patient and follow the giving instruction and hp wireless printer setup.

Asus Z490 stuff