10-04-2022 06:30 AM - edited 10-18-2023 07:20 AM
ill use this thread to collect some new test bioses for the boards, maybe also to explain some less understood options
to disable cores ccd go here and choose ccd xx bit map down core.
each ones stand for an enabled core
best to disable from the back, ie:
110000
instead of 0011000
after selection press downcore apply changes or discard if made mistake
ocpak/octools
FAQ:
7950x not boosting pass 5.5G -> check that CStates is not disabled
Detailed Explanation on CState Boot Limiter
Test BIOSes:
new:
X3D OC Preset for those MB with asynch BCLK Support: (for simple slight perf boost for X3D)
DOCP/EXPO Tweaked: (for simple timings tightening)
strixe-e 1515
for crosshair and strix e-e:
explanation of segment2 Loadline:
customize a heterogenous loadline for a dual segment workload range.
example above shows loadline=L6 when current is in range of 0~40A, and Level4 when current is above 40A.
Adds for x3d
dynamic ccd priority switch with core flex, os / driver agnostic so win10 win11 ok
Algo as follows:
If condition reached and ccd0 specified, then check current mem/cache activity > threshold and hysteresis reached, if fulfilled then switch
If condition reached and ccd1 specified, then check current mem/cache activity <=threshold and hysteresis reached,, if fulfilled then switch
Default hysteresis =4
Can combine multiple algos for ccd priority so combinations are wide
works on non x3d too but of course senseless on it. detailed explanation here.
Solved! Go to Solution.
04-22-2023 05:12 PM
I just updated to 1202 without issues using MCR, power down, PBO -30. Hopefully things stay well, x670 Extreme and 7950x.
04-22-2023 11:29 PM
Same here .
1001 to 1202 BIOS ist runing fine with 7800X3D PBO on -20 CO DDR5 6000 very sharp subtimings MCR PowerDown enable.
Strix X670 E-A
04-22-2023 11:47 PM
@Thunderburne
Did you Test your Stability with Karhu and AIda64, Memtest?
With MCR and PD it "looks" good first, but some Tests like mentioned above are unstable and produce errors
04-23-2023 12:28 AM - edited 04-23-2023 12:44 AM
04-23-2023 12:47 AM - edited 04-23-2023 12:49 AM
Karhu isnt free- its 10 Euros, but worth it. believe me
Karhu: on "Advanced"-Tab set - "CPU cache" to "Enabled"
When i have PD and MCR on Auto i have 0 Errors (Testet until 5000% yesterday), when i Enable MCR and PD i have the first error at around 100%
-Errors under 1000% can be caused by wrong voltages ->"stress Memory"-> VDIMM, "stress cache"-> VSoc
i tried VSoc between 1.1 and 1.35 (which was at 1004 at 1.35 V by default...............") no changes
-Errors between 1000% and 5000% can be caused by wrong ProcODT and / or RTT - i did not make changes yet here
Aida64 Stresstest Crashes instant when i raise FCLK by 33Mhz or when have BCLK on 102% and higher (with 0805 ABCLK 103% was no Problem)
04-23-2023 12:57 AM
Thank you for the Settings i will Show this.
I playd yester day TlOU an a Long Time Call of Duty without problems .
I Check this.
04-23-2023 01:11 AM
If you own a x670Hero or an X670Extreme - you have a full Aida64 Version. You dont have to buy it then. You can install AIDA 64 by ArmoryCrate or it is on your USB Stick-which was deliverd with your Mainboard. So you dont have to use the trial Version of AIDA64
04-23-2023 01:14 AM - edited 04-23-2023 01:19 AM
Kahru @ 1000% in diesem Moment.
Ich habe ein Strix X670E-A.
Ich versuche Aida Testversion nach Kahru.
I dont have BLCK OC only CO -20.
04-23-2023 01:24 AM - edited 04-23-2023 03:11 AM
Can you share your Voltages?
VSoc
VDimm
Proc ODT
Timings: Trefi
Best would be a ZenTimingsScreenshot like this
04-23-2023 09:41 AM
Kahru crashed @2100%
The Problem was no Fan on the GSkill RAM because the Temperatur Hits 56 degrease after Fan Installation and 43 degrease the Cache Test ist running .