cancel
Showing results for 
Search instead for 
Did you mean: 

X670 resource

Shamino
Moderator

ill use this thread to collect some new test bioses for the boards, maybe also to explain some less understood options

to disable cores ccd go here and choose ccd xx bit map down core.
each ones stand for an enabled core
best to disable from the back, ie:
110000
instead of 0011000
after selection press downcore apply changes or discard if made mistake

ocpak/octools

FAQ:
7950x not boosting pass 5.5G -> check that CStates is not disabled
Detailed Explanation on CState Boot Limiter


Test BIOSes:

new:
X3D OC Preset for those MB with asynch BCLK Support: (for simple slight perf boost for X3D)
97792

DOCP/EXPO Tweaked: (for simple timings tightening)
97793

strixe-e 1515 

strixe-f 1515 

strix e a 1515 

crosshair hero 1515 

crosshair gene 1515 

crosshair extreme 1515 

creator 670 1515

creator b650 1515

strix 650E I

strix 670 itx

 

 

for crosshair and strix e-e:

explanation of segment2 Loadline:

dualseg.jpg

customize a heterogenous loadline for a dual segment workload range.

example above shows loadline=L6 when current is in range of 0~40A, and Level4 when current is above 40A.

 

 

 


Adds for x3d

dynamic ccd priority switch with core flex, os / driver agnostic so win10 win11 ok

97403

97404

Algo as follows:
If condition reached and ccd0 specified, then check current mem/cache activity > threshold and hysteresis reached, if fulfilled then switch
If condition reached and ccd1 specified, then check current mem/cache activity <=threshold and hysteresis reached,, if fulfilled then switch
Default hysteresis =4

Can combine multiple algos for ccd priority so combinations are wide

works on non x3d too but of course senseless on it. detailed explanation here.

4,114 Views
2,403 REPLIES 2,403

@Shamino No, its under a custom loop, and was idling at about 36 ° C. A friend of me had the same happening to him with his 7900x3d. His was not overheating as well.  I switched back to 1101 and limited soc voltage to 1.3 manually, no problems at all. but not feeling safe 😞


@dg1qktr wrote:

limited soc voltage to 1.3 manually, no problems at all. but not feeling safe 😞


Check your VSOC under windows, 1.3 fixed will probly be higher once LLC made its job.

Hwinfo says 1.3

Mine says 1.235 VDDCR_SOC and 1.288 CPU SOC for 1.25 in the bios, you're lucky 😁

hi dg1 may i know the board u are using? i was thinking of asking you to try one whereby the temperature reads need to be consecutively over 95c twice before taking action to prevent a false reading

Asus crosshair x670e hero, I am Dg1qkt. For some reason I haven’t another account on my mobile 

We need a stable bios even for non x3d, 7950x on my hero with Expo Enhanced and pbo limit thermal 80º and everything else default auto sets in bios 1.349v for CPU VSoC , yet after monitoring it actually spikes above 1.35v. and bad things starts to happen have been like this on any bios after 0805, tested almost sall bios now gone.

Currently on 1202  i have to set either manually to 1.30v or if i set a negative offset of 0.05V it actually sets to around 1.19v , so something fishy here because why on auto it sets to 1.349 and s negative offset on only 0.05V actually lowers it so much? And i tested on load and observed it actually does not go higher plus performance is degraded a bit.

So for now only solution for me is set 1.30v on CPU VSoC and system is stable.

according to latest comm from AMD  we should gave a new AGESA to fix this as to limit to 1.30v VSoC, so please apply it to a stable BIOS ASAP.

ftln46
Level 9

Current settings for my X670E Gene, only high temps I get are DDR5 SPD due to 1.6v on the dimms:

[2023/04/27 21:51:25]
Ai Overclock Tuner [DOCP I]
DOCP [DDR5-7600 36-46-46-121-1.40V-1.40V]
eCLK Mode [Auto]
BCLK1 Frequency [100.0000]
Memory Frequency [DDR5-6200MHz]
FCLK Frequency [2067 MHz]
Core Performance Boost [Auto]
Tcl [26]
Trcd [37]
Trp [37]
Tras [30]
Trc [56]
Twr [48]
Refresh Interval [65535]
Trfc1 [477]
Trfc2 [Auto]
Trfcsb [Auto]
Trtp [10]
TrrdL [6]
TrrdS [4]
Tfaw [20]
TwtrL [14]
TwtrS [4]
TrdrdScl [4]
TrdrdSc [1]
TrdrdSd [Auto]
Trdrddd [Auto]
TwrwrScl [2]
TwrwrSc [1]
TwrwrSd [Auto]
TwrwrDd [Auto]
Twrrd [2]
Trdwr [14]
IBUF_LPWR_MODE [Auto]
ADDR_CMD_MODE [Auto]
M_ORDERING [Auto]
S_COL_WIDTH [Auto]
MC_SVA_TRIM0 [Auto]
MC_SVA_TRIM1 [Auto]
MC_SVA_TRIM2 [Auto]
Proc CA Drive Strength [Auto]
Proc Data Drive Strength [Auto]
CPU On-Die Termination [Auto]
DRAM Data Drive Strength [Auto]
Rtt Nom Wr [Auto]
Rtt Nom Rd [Auto]
Rtt Wr [Auto]
Rtt Park [Auto]
Rtt Park Dqs [Auto]
Power Down Enable [Disabled]
Memory Context Restore [Auto]
UCLK DIV1 MODE [UCLK=MEMCLK]
Bank Swap Mode [Auto]
Mem Over Clock Fail Count [Auto]
Medium Load Boostit [Auto]
Precision Boost Overdrive [Auto]
Precision Boost Overdrive Scalar [Auto]
CPU Boost Clock Override [Auto]
Per-Core Boost Clock Limit [Auto]
Platform Thermal Throttle Limit [Auto]
Curve Optimizer [All Cores]
All Core Curve Optimizer Sign [Negative]
All Core Curve Optimizer Magnitude [10]
GFX Curve Optimizer [Auto]
VRM Initialization Check [Enabled]
CPU Load-line Calibration [Auto]
CPU Current Capability [Auto]
CPU Current Reporting Scale [Auto]
Core Voltage Suspension [Auto]
CPU VRM Switching Frequency [Auto]
VRM Spread Spectrum [Auto]
CPU Power Duty Control [T.Probe]
CPU Power Phase Control [Auto]
VDDSOC Load-line Calibration [Auto]
VDDSOC Current Capability [Auto]
VDDSOC Current Reporting Scale [Auto]
VDDSOC Switching Frequency [Auto]
VDDSOC Power Phase Control [Auto]
DRAM Current Capability [Auto]
DRAM Switching Frequency [Auto]
DRAM Power Phase Control [Extreme]
MISC Switching Frequency [Auto]
Performance Bias [Auto]
Clock Spread Spectrum [Auto]
Runtime BCLK OC [Auto]
BCLK1 Amplitude [Auto]
BCLK1 Slew Rate [Auto]
1.8V PLL Voltage [Auto]
1.8V Standby Voltage [Auto]
Misc_ALW [Auto]
Chipset0 VDD Voltage [Auto]
Chipset1 VDD Voltage [Auto]
CPU 3.3V [Auto]
DDR_testA [Auto]
DDR_testB [Auto]
SMU_Comp1 [Auto]
SMU_Comp2 [Auto]
SMU_Comp3 [Auto]
R1 [Auto]
R2 [Auto]
R3 [Auto]
Sense MI Skew 1 [Auto]
Sense MI Skew 1 [Auto]
Sense MI Skew 2 [Auto]
Sense MI Skew 2 [Auto]
Sense MI Skew 3 [Auto]
Sense MI Skew 3 [Auto]
Sense MI Skew 4 [Auto]
Sense MI Skew 4 [Auto]
Raise RComp [Auto]
Dummy VOutA [Auto]
Dummy VOutB [Auto]
Algorithm 1 [Enabled]
Algorithm 1 Condition [Core Current]
Algorithm 1 Action [CCD Priority]
Level1 Threshold Value [20]
Level2 Threshold Value [50]
Level1 Action Value [1]
Level2 Action Value [0]
Level3 Action Value [1]
Algorithm 2 [Auto]
Algorithm 3 [Auto]
CCD Priority Memory Activity Threshold [1070]
CCD Priority Hysteresis [Auto]
Cooler Efficiency Customize [Keep Training]
Cooler Re-evaluation Algorithm [Normal]
Optimism Scale [100]
CPU SOC Voltage [Manual Mode]
- VDDSOC Voltage Override [1.25000]
CPU VDDIO / MC Voltage [Manual Mode]
- VDDIO Override [1.25190]
Misc Voltage [Auto]
VDDP Voltage [Auto]
High DRAM Voltage Mode [Enabled]
DRAM VDD Voltage [1.60000]
DRAM VDDQ Voltage [1.45000]
PMIC Force Continuous Current Mode [Auto]
PMIC Voltages [Sync All PMICs]
SPD HUB VLDO (1.8V) [Auto]
SPD HUB VDDIO (1.0V) [Auto]
Memory VDD Voltage [1.60000]
Memory VDDQ Voltage [1.45000]
Memory VPP Voltage [Auto]
Memory Voltage Switching Frequency [Auto]
Memory Current Capability [Auto]
Security Device Support [Enable]
SHA256 PCR Bank [Enabled]
Pending operation [None]
Platform Hierarchy [Enabled]
Storage Hierarchy [Enabled]
Endorsement Hierarchy [Enabled]
Physical Presence Spec Version [1.3]
Disable Block Sid [Disabled]
Firmware TPM switch [Enable Firmware TPM]
Erase fTPM NV for factory reset [Enabled]
Password protection of Runtime Variables [Enable]
PSS Support [Enabled]
NX Mode [Enabled]
SVM Mode [Enabled]
Resize BAR Support [Enabled]
SR-IOV Support [Disabled]
Legacy USB Support [Enabled]
XHCI Hand-off [Enabled]
USB Mass Storage Driver Support [Enabled]
OWC TB3 SD Card Reader 1616 [Auto]
OWC TB3 SD Card Reader 1616 [Auto]
USB3.0 FLASH DRIVE PMAP [Auto]
USB3.0 FLASH DRIVE PMAP [Auto]
U32G2_3 [Enabled]
U32G2_4 [Enabled]
U32G2X2_C6 [Enabled]
USB_P8 [Enabled]
USB_P9 [Enabled]
U32G1_10 [Enabled]
U32G1_11 [Enabled]
USB16 [Enabled]
USB17 [Enabled]
U32G2_C18 [Enabled]
LAN_U32G2_19 [Enabled]
U32G2_20 [Enabled]
U32G2_21 [Enabled]
KBMS_USB22 [Enabled]
KBMS_USB23 [Enabled]
Network Stack [Disabled]
Device [N/A]
SATA Controller(s) [Disabled]
NVMe RAID mode [Disabled]
SMART Self Test [Enabled]
Restore AC Power Loss [Power Off]
ErP Ready [Disabled]
Max Power Saving [Disabled]
Power On By PCI-E [Disabled]
Power On By RTC [Disabled]
CPU PCIE ASPM Mode Control [Auto]
PCIEX16_1 Bandwidth Bifurcation Configuration [Auto Mode]
USB Audio Controller [Disabled]
Wi-Fi Controller [Disabled]
Bluetooth Controller [Enabled]
When system is in working state [All On]
Q-Code LED Function [Auto]
When system is in sleep, hibernate or soft off states [All On]
Intel LAN Controller [Disabled]
USB power delivery in Soft Off state (S5) [Enabled]
U32G2_C18 Type C Power Mode [Auto]
Alteration Mode Switch [PCIE Link Speed]
PCIEX16 Link Mode [Auto]
M.2 Link Mode [Auto]
Chipset_1 Link Mode [Auto]
GEN-Z.2_1 Link Mode [Auto]
GEN-Z.2_2 Link Mode [Auto]
Chipset_2 Link Mode [Auto]
PCIEX1 Link Mode [Auto]
Primary Video Device [PCIE Video]
Integrated Graphics [Disabled]
Global C-state Control [Auto]
IOMMU [Auto]
ECC [Auto]
SMT Control [Auto]
Core Performance Boost [Auto]
L1 Stream HW Prefetcher [Auto]
L2 Stream HW Prefetcher [Auto]
L1 Stride Prefetcher [Auto]
L1 Region Prefetcher [Auto]
L2 Up/Down Prefetcher [Auto]
Core Watchdog Timer Enable [Disabled]
Platform First Error Handling [Auto]
Opcache Control [Auto]
Streaming Stores Control [Auto]
Local APIC Mode [Auto]
ACPI _CST C1 Declaration [Auto]
MCA error thresh enable [Auto]
SMU and PSP Debug Mode [Auto]
PPIN Opt-in [Auto]
Enhanced REP MOVSB/STOSB [Enabled]
REP-MOV/STOS Streaming [Enabled]
Xtrig7 Workaround [Auto]
SNP Memory (RMP Table) Coverage [Auto]
SMEE [Auto]
Action on BIST Failure [Auto]
PAUSE Delay [Auto]
Power Supply Idle Control [Auto]
Memory interleaving [Auto]
Memory interleaving size [Auto]
DRAM map inversion [Auto]
Location of private memory regions [Auto]
ACPI SRAT L3 Cache As NUMA Domain [Auto]
Disable DF to external downstream IP Sync Flood Propagation [Auto]
Disable DF sync flood propagation [Auto]
Freeze DF module queues on error [Auto]
DF Cstates [Auto]
PSP error injection support [False]
Active Memory Timing Settings [Auto]
Processor CK drive strengths [Auto]
Processor CA drive strengths [Auto]
Processor CS drive strengths [Auto]
Dram ODT impedance RTT_NOM_WR [Auto]
Dram ODT impedance RTT_NOM_RD [Auto]
Dram ODT impedance RTT_WR [Auto]
Dram ODT impedance RTT_PARK [Auto]
Dram ODT impedance DQS_RTT_PARK [Auto]
Processor ODT impedance [Auto]
Processor DQ drive strengths [Auto]
Dram DQ drive strengths [Auto]
Power Down Enable [Auto]
Disable Memory Error Injection [Auto]
TSME [Auto]
Data Scramble [Auto]
Chipselect Interleaving [Auto]
Address Hash Bank [Auto]
Address Hash CS [Auto]
Address Hash Subchannel [Auto]
BankSwapMode [Auto]
DFE Read Training [Auto]
DRAM PDA Enumerate ID Programming Mode [Auto]
TX DFE Taps [Auto]
PPT Control [Auto]
MBIST Enable [Auto]
Memory Context Restore [Auto]
OC Recovery Fail Count [1]
PCIe ARI Support [Auto]
PCIe All Port ECRC [Auto]
Advanced Error Reporting (AER) [Auto]
PCIe ARI Enumeration [Auto]
PSPP Policy [Auto]
UMA Version [Auto]
GPU Host Translation Cache [Auto]
NB Azalia [Auto]
Audio IOs [Auto]
PCIe loopback Mode [Auto]
CPPC Dynamic Preferred Cores [Auto]
ECO Mode [Disable]
TDP Control [Auto]
PPT Control [Auto]
Thermal Control [Auto]
TDC Control [Auto]
EDC Control [Auto]
PROCHOT Control [Auto]
Fan Control [Auto]
VDDP Voltage Control [Auto]
Infinity Fabric Frequency and Dividers [Auto]
FEATURE FCLK DPM [Auto]
SyncFifo Mode Override [Auto]
GFXOFF [Auto]
CPU Temperature [Monitor]
CPU Package Temperature [Monitor]
MotherBoard Temperature [Monitor]
VRM Temperature [Monitor]
Chipset 1 Temperature [Monitor]
Chipset 2 Temperature [Monitor]
T_Sensor Temperature [Monitor]
DIMM A Temperature [Monitor]
DIMM B Temperature [Monitor]
CPU Fan Speed [Monitor]
CPU Optional Fan Speed [Monitor]
Chassis Fan Speed [Monitor]
AIO Pump Speed [Monitor]
CPU Core Voltage [Monitor]
12V Voltage [Monitor]
5V Voltage [Monitor]
3.3V Voltage [Monitor]
CPU VDDIO / MC Voltage [Monitor]
HYDRANODE Fan Association [Disabled]
CPU Fan Q-Fan Control [PWM Mode]
CPU Fan Profile [Manual]
CPU Fan Step Up [Level 0]
CPU Fan Step Down [Level 0]
CPU Fan Speed Low Limit [200 RPM]
CPU Fan Point4 Temperature [70]
CPU Fan Point4 Duty Cycle (%) [100]
CPU Fan Point3 Temperature [60]
CPU Fan Point3 Duty Cycle (%) [50]
CPU Fan Point2 Temperature [45]
CPU Fan Point2 Duty Cycle (%) [30]
CPU Fan Point1 Temperature [20]
CPU Fan Point1 Duty Cycle (%) [30]
Chassis Fan Q-Fan Control [PWM Mode]
Chassis Fan Profile [Manual]
Chassis Fan Q-Fan Source [CPU]
Chassis Fan Step Up [Level 0]
Chassis Fan Step Down [Level 0]
Chassis Fan Speed Low Limit [200 RPM]
Chassis Fan Point4 Temperature [75]
Chassis Fan Point4 Duty Cycle (%) [100]
Chassis Fan Point3 Temperature [60]
Chassis Fan Point3 Duty Cycle (%) [50]
Chassis Fan Point2 Temperature [45]
Chassis Fan Point2 Duty Cycle (%) [40]
Chassis Fan Point1 Temperature [20]
Chassis Fan Point1 Duty Cycle (%) [30]
AIO Pump Q-Fan Control [DC Mode]
AIO Pump Profile [Manual]
AIO Pump Q-Fan Source [CPU]
AIO Pump Step Up [Level 0]
AIO Pump Step Down [Level 0]
AIO Pump Speed Low Limit [Ignore]
AIO Pump Point4 Temperature [70]
AIO Pump Point4 Duty Cycle (%) [80]
AIO Pump Point3 Temperature [60]
AIO Pump Point3 Duty Cycle (%) [80]
AIO Pump Point2 Temperature [50]
AIO Pump Point2 Duty Cycle (%) [80]
AIO Pump Point1 Temperature [20]
AIO Pump Point1 Duty Cycle (%) [80]
Launch CSM [Disabled]
OS Type [Windows UEFI mode]
Secure Boot Mode [Standard]
Fast Boot [Disabled]
Boot Logo Display [Auto]
POST Delay Time [5 sec]
Bootup NumLock State [On]
Wait For 'F1' If Error [Enabled]
Option ROM Messages [Force BIOS]
Interrupt 19 Capture [Disabled]
AMI Native NVMe Driver Support [Enabled]
Setup Mode [Advanced Mode]
BIOS Image Rollback Support [Enabled]
Publish HII Resources [Disabled]
Flexkey [Reset]
Setup Animator [Disabled]
Load from Profile [1]
Profile Name []
Save to Profile [1]
DIMM Slot Number [DIMM_A]
Download & Install ARMOURY CRATE app [Disabled]
Download & Install MyASUS service & app [Disabled]
Special Display Features [Disabled]
D3Cold Support [Disabled]
Discrete GPU _DSM Function A [Disabled]
Discrete GPU _DSM Function B [Disabled]
NVIDIA DGPU Power Enable [Disabled]
Non-Eval Discrete GPU Support [Enabled]
Discrete GPU HPD Circuitry [OR Circuitry]
Discrete GPU's USB Port [Keep Default Setting]
Discrete GPU's SSID/SVID [Keep Default Setting]
Discrete GPU BOMACO Support [Disabled]
Thunderbolt / USB4 Support [Enabled]
Thunderbolt / USB4 Security Level [No Security]
Thunderbolt / USB4 MMIO Resource [Full Size]
Thunderbolt / USB4 Wake Up Command [GO2SX Command]
Processor Aggregator Device [Enabled]
Core Count Control [Enabled]
SMT Control [Auto]
Active Memory Timing Settings [Auto]
Processor CA drive strengths [Auto]
Processor DQ drive strengths [Auto]
Processor ODT impedance [Auto]
Dram DQ drive strengths [Auto]
Dram ODT impedance RTT_NOM_WR [Auto]
Dram ODT impedance RTT_NOM_RD [Auto]
Dram ODT impedance RTT_WR [Auto]
Dram ODT impedance RTT_PARK [Auto]
Dram ODT impedance DQS_RTT_PARK [Auto]
Power Down Enable [Auto]
Infinity Fabric Frequency and Dividers [Auto]
UCLK DIV1 MODE [Auto]
Precision Boost Overdrive [Auto]
VDDG Voltage Control [Auto]
VDDP Voltage Control [Auto]
SoC/Uncore OC Mode [Auto]
SoC Voltage [0]
VDD Misc Control [Auto]
LCLK Frequency Control [Auto]
VDDIO Ctrl [Auto]
Enable Platform PMIC Control [Auto]
VPP Ctrl [Auto]

Shamino
Moderator

for the hardware monitor readback levels, please comprehend the difference between die sense and socket sense , socket sense is higher than actual -> dont get carried away by youtubers looking for clicks

Select boards have die sense on select rails.

google and read

 

Shamino_0-1682670011984.png

 

 

SHAMINO - can you tell us something about safe voltages range it those cases:

Here are my bios readings from 7950X3D and Strix x670e-e newest bios 1301:
1- CPU SOC - AUTO is 1,024V and EXPO is 1,244V (but in stress 1,305V in windows testers - weird bump)
2- CPU VDDIO/MC VOLTAGE - AUTO is 1,137V and EXPO is 1,439V (stress 1,447V in testers - looks high)
3- MISC VOLTAGE - almost still 1,137-1,146V (looks good)
4- VDDP - AUTO is 0,799V and EXPO is 1,148V (looks hmmm - not too high ?)

If we talk about SOC - in older bioses it was much higher - now it looks ok but still bad voltage boost idle/load - big differences in readings up to 1,305V.
VDDIO/MC VOLTAGE - I think it is too high and 1,4V + looks bad - I tried lower to 1,3V (memory errors), but for now manual 1,35V = 1,38V in bios reading = 1,4V in stressing, looks stable but still weird unknown voltage bump. 

In bios my settings standard is - set EXPO or EXPO Tweaked, PBO 80*C, disable integrated GPU and thats it (sometimes powerdown / mem context restore).