X670 resource

[Shamino]

ill use this thread to collect some new test bioses for the boards, maybe also to explain some less understood options

to disable cores ccd go here and choose ccd xx bit map down core.
each ones stand for an enabled core
best to disable from the back, ie:
110000
instead of 0011000
after selection press downcore apply changes or discard if made mistake

ocpak/octools
octool port to linux

FAQ:
7950x not boosting pass 5.5G -> check that CStates is not disabled
Detailed Explanation on CState Boot Limiter


Test BIOSes:

new:
X3D OC Preset for those MB with asynch BCLK Support: (for simple slight perf boost for X3D)


DOCP/EXPO Tweaked: (for simple timings tightening)



strixe-e 1003
strixe-e 1004 (fixed a hi dram v mode enabled bug + Fix Non-UEFI VGA card cannot display issue ) *note :"pulled support of 24/48gb ram due to request to wait for official firmware release"

strix e f 1003
strix e f 1004 (fixed a hi dram v mode enabled bug + Fix Non-UEFI VGA card cannot display issue ) *note :"pulled support of 24/48gb ram due to request to wait for official firmware release"

strix e a 1003
strix e a 1004 (fixed a hi dram v mode enabled bug + Fix Non-UEFI VGA card cannot display issue ) *note :"pulled support of 24/48gb ram due to request to wait for official firmware release"

strix itx 1003

crosshair hero 1003
crosshair hero 1004 (fixed a hi dram v mode enabled bug + Fix Non-UEFI VGA card cannot display issue ) *note :"pulled support of 24/48gb ram due to request to wait for official firmware release"

crosshair gene 1003
crosshair gene 1004    (fixed a hi dram v mode enabled bug + Fix Non-UEFI VGA card cannot display issue ) *note :"pulled support of 24/48gb ram due to request to wait for official firmware release"

crosshair extreme 1003
crosshair extreme 1004  (fixed a hi dram v mode enabled bug + Fix Non-UEFI VGA card cannot display issue ) *note :"pulled support of 24/48gb ram due to request to wait for official firmware release"

creator 670 1003
creator 670 1004 (fixed a hi dram v mode enabled bug + Fix Non-UEFI VGA card cannot display issue ) *note :"pulled support of 24/48gb ram due to request to wait for official firmware release"

B650 creator 1003
B650 creator 1004 (fixed a hi dram v mode enabled bug + Fix Non-UEFI VGA card cannot display issue ) *note :"pulled support of 24/48gb ram due to request to wait for official firmware release"

Adds for x3d

dynamic ccd priority switch with core flex, os / driver agnostic so win10 win11 ok





Algo as follows:
If condition reached and ccd0 specified, then check current mem/cache activity > threshold and hysteresis reached, if fulfilled then switch
If condition reached and ccd1 specified, then check current mem/cache activity <=threshold and hysteresis reached,, if fulfilled then switch
Default hysteresis =4

Can combine multiple algos for ccd priority so combinations are wide

works on non x3d too but of course senseless on it. detailed explanation here.

[D4NK3STM3M3S]

Based on that information, you're probably be right about it not being the BIOS. It might just be a bug that says there's an issue but there is nothing really wrong.

In the new 1004 test BIOS Shamino posted, theres a fix labeled "Non-UEFI VGA card cannot display issue" so maybe it's connected to that.

[tommy76000]

1004: fixed a hi dram v mode enabled bug + Fix Non-UEFI VGA card cannot display issue

@ShaminoIs this hi dram v mode connected to issues with MCR?

Thanks for fixing this Non-UEFI VGA card cannot display issue 🙂

[Shamino]

no , totally unrelated

[Apothocary]

24/48GB module support pulled in 1003, too?

[Shamino]

no its just 1004

[DNABrooker]

I got the X670e Extreme Board with a 7950x3D with 32GB GSKILL 6000 CL30, i get some random popups with the following Message:

"WARNING!: WARNING! Water leak detected. For system safety, the system will shut down in 5 seconds."

I didnt have any Leak detection sensor plugged in, i can reproduce this in certain games.

Can somebody help with it?

[Braegnok]

Thanks for all your hard work!

I loaded 1004 this afternoon, everything is working great on Gene. 

[Bix]

Hi,

First, thanks for sharing all of this.

However, I don't know what exactly does the 'Get VF' function from your tool but it made my PC die.

Motherboard X670e-f won't initialize anymore, no led, only some fans running.

[BoostedSTIG]

Anyone having weird PCIe device detection issues? I've not had any issue detecting my GPU in the top x16 slot. But I have a Startech 4 controller USB 3.0 expansion card that is x4 in the bottom most slot on my Strix X670e-f and I've had a couple of times where it just seems not to initialize and therefore I have none of my USB devices that are on that card. Windows doesn't see the device at all when this happens. A reboot seems to fix it almost 100% of the time. I just can't seem to replicate the issue. It's not a deal breaker at the moment, but it is more than just slightly annoying. 

[BoostedSTIG]

Update: Seems to be that on cold boot, the PCIe USB card would not initialize. Was able to repeat this a few times. Card would be recognized on a reboot, but not on a cold boot. MCR and Power down were set to enabled. 
I put MCR and Power Down back on Auto in BIOS, and now it seems to be detecting the PCIe expansion card every time. 
BIOS 1003