cancel
Showing results for 
Search instead for 
Did you mean: 

X670 resource

Shamino
Moderator

ill use this thread to collect some new test bioses for the boards, maybe also to explain some less understood options

to disable cores ccd go here and choose ccd xx bit map down core.
each ones stand for an enabled core
best to disable from the back, ie:
110000
instead of 0011000
after selection press downcore apply changes or discard if made mistake

ocpak/octools

FAQ:
7950x not boosting pass 5.5G -> check that CStates is not disabled
Detailed Explanation on CState Boot Limiter


Test BIOSes:

new:
X3D OC Preset for those MB with asynch BCLK Support: (for simple slight perf boost for X3D)
97792

DOCP/EXPO Tweaked: (for simple timings tightening)
97793

strixe-e 1515 

strixe-f 1515 

strix e a 1515 

crosshair hero 1515 

crosshair gene 1515 

crosshair extreme 1515 

creator 670 1515

creator b650 1515

strix 650E I

strix 670 itx

 

 

for crosshair and strix e-e:

explanation of segment2 Loadline:

dualseg.jpg

customize a heterogenous loadline for a dual segment workload range.

example above shows loadline=L6 when current is in range of 0~40A, and Level4 when current is above 40A.

 

 

 


Adds for x3d

dynamic ccd priority switch with core flex, os / driver agnostic so win10 win11 ok

97403

97404

Algo as follows:
If condition reached and ccd0 specified, then check current mem/cache activity > threshold and hysteresis reached, if fulfilled then switch
If condition reached and ccd1 specified, then check current mem/cache activity <=threshold and hysteresis reached,, if fulfilled then switch
Default hysteresis =4

Can combine multiple algos for ccd priority so combinations are wide

works on non x3d too but of course senseless on it. detailed explanation here.

2,023 Views
2,948 REPLIES 2,948

Owner5566
Level 8
Shamino wrote:

hero

Currently testing this Bios.
trefi works, brings more performance.
But CPU Boost Clocks are much lower.
only with +200 Override i can reach 5.7 in single clock effective while testing with BoostTester and that although it would "want" to achieve 5.9.
In 0801 for example i had seen also 5.8Ghz+ with +100 on Override and negative CO values on cores
Is this related to new AGESA? Or can you fix it.
95955

Owner5566 wrote:
Currently testing this Bios.
trefi works, brings more performance.
But CPU Boost Clocks are much lower.
only with +200 Override i can reach 5.7 in single clock effective while testing with BoostTester and that although it would "want" to achieve 5.9.
In 0801 for example i had seen also 5.8Ghz+ with +100 on Override and negative CO values on cores
Is this related to new AGESA? Or can you fix it.
95955


I think it's the AGESA, but HWINFO64 is no performance metric, when I run benchmarks performance is still the same as older bios even though HWINFO64 shows lower boost. I wouldn't worry too much.
R9 7950X - ASUS X670E Crosshair Extreme (bios 0803) - 32GB HyperX Fury Beast @6200c32 - Corsair H150i Pro - ASUS RTX3080 TUF OC V2 - Phanteks P400A - Corsair RM850 - WD SN850

Tsikos
Level 10
This problem come from a new member who can't post here yet @Shafiullah

He have an Asus X670E-HERO and he used 4 DIMM at the max capacity 128gb the problem is the ram speed is locked to 3600mhz, is that a problem or it must work like that by default?

https://imgur.com/RNZpUnj

https://imgur.com/undefined

https://imgur.com/EdMnMxx

Tsikos wrote:
This problem come from a new member who can't post here yet @Shafiullah

He have an Asus X670E-HERO and he used 4 DIMM at the max capacity 128gb the problem is the ram speed is locked to 3600mhz, is that a problem or it must work like that by default?

https://imgur.com/RNZpUnj

https://imgur.com/undefined

https://imgur.com/EdMnMxx


I am on the Crosshair Extreme, also using 4x32GB of memory. Left on auto settings it will indeed tune itself to 3600 speed, and that is the documented supported speed for 4 sticks. I'm feeling rather lucky this early on in the platform's life that I can get it running at that density and with mixing two 64GB kits (albeit identical ones) stable at all (and on the board's original BIOS it didn't, I would BSOD, but as of 0705 I am fine).

I haven't tried to apply EXPO settings to the 4 sticks because, frankly, I don't think there's a chance in hell of it working and I don't want to lose current memory training which is thoroughly tested 100% stable. But when the next BIOS comes out and I'm going to have to lose the current memory training anyway, I'll give it a shot setting it to EXPO (5200 on my sticks) just to see what happens. On the board's original BIOS, I couldn't get that to even post.

Tsikos wrote:
This problem come from a new member who can't post here yet @Shafiullah

He have an Asus X670E-HERO and he used 4 DIMM at the max capacity 128gb the problem is the ram speed is locked to 3600mhz, is that a problem or it must work like that by default?

https://imgur.com/RNZpUnj

https://imgur.com/undefined

https://imgur.com/EdMnMxx


Hello. This is me, My ID is shafy7 (not shafiullah) Still try to figure out on max Speed for my 128GB ram

Shafy14 wrote:
Hello. This is me, My ID is shafy7 (not shafiullah) Still try to figure out on max Speed for my 128GB ram


@shamino do you this the firmware update will resolve the issue of not running at 6000mhz speed (128gb. )Â*

Shafy14 wrote:
@shamino do you this the firmware update will resolve the issue of not running at 6000mhz speed (128gb. )Â*


no, 4X32gb dual rank will struggle to run at 4800 , this is a memory controller limitation, 6000 is out of the question. i would not waste my time waiting for this to happen.

Shamino wrote:
no, 4X32gb dual rank will struggle to run at 4800 , this is a memory controller limitation, 6000 is out of the question. i would not waste my time waiting for this to happen.


@shamino thank you. You would advice to run 2x32gb at 6000mhz or 128gb 4800.Â*

I’m using for simulation and and 3d work Â*

Shafy14 wrote:
@shamino thank you. You would advice to run 2x32gb at 6000mhz or 128gb 4800.Â*

I’m using for simulation and and 3d work Â*


since you already have 128GB installed, run your simulation tasks and check task manager to see how much memory is being utilized at its peak and how much Memory is left. if it's below 50GB you should get by fine and have enough buffer to run 2x32 at 6000.

Totday i flash 0804 on my Strix E and working but flash over flashback not work. Only normal flash working, very strange. USB stick is fat32 and rename the bios file correct with BIOSRenamer. The latest flashback with 0705 working but not with 0804.